PANAMAX M5400PM 11 Outlet Home Theater Power Conditioner

Level 4+ Power Cleaning and Linear Filtration eliminates common symptoms of contaminated power (including loss of detail, pops, hisses, hums and visual artifacts) and allows your A/V equipment to perform up to its full capability. Panamax's patent pending AVM circuitry continuously monitors the incoming power as displayed on the digital voltmeter. In case of an undervoltage or an overvoltage, a flashing lightning bolt will be displayed in red in the voltmeter, and power to the connected equipment is automatically turned off if either of these conditions is detected. When voltage returns to a safe level, power to the equipment is automatically reconnected with the PANAMAX M5400PM 11 Outlet Home Theater Power Conditioner.

Voltage Regulation

Regulates the output voltage on Banks 1-4 to 120 VAC ± 5 VAC. This is accomplished through two boost stages and one buck stage of voltage regulation. In Boost Stage 1 the voltage is boosted in the 109-119V range, while Boost Stage 2 boosts the voltage in the 100-109V range. The Buck Stage acts to reduce voltage in the 125-136V range. LiFT Technology EMI/RFI Noise Filtration : Your audio/video components are constantly being bombarded by electromagnetic interference (EMI) and radio frequency interference (RFI) through their AC power source. This contaminated power can affect audio/video equipment and will degrade the overall performance of your entire system. Common symptoms of contaminated power include loss of picture detail, dull colors, pops, hisses, hums and visual artifacts.

Automatic Over and Under Voltage Protection (AVM)
Panamax's patent pending power monitoring circuitry constantly monitors the AC line voltage for unsafe voltage conditions such as momentary spikes or prolonged over-voltages and under-voltages (brownouts). These unsafe conditions pose a very dangerous threat to all electronic equipment within the home. If the MAX 5400-PM senses an unsafe power condition, it will automatically disconnect your equipment from the power to protect equipment from damage.Once the voltage returns to a safe level, the M5400-PM will automatically reconnect the power. When subjected to a 6,000V (open circuit voltage) / 500A (short circuit current) surge, the M5400-PM limits its voltage output to less than 330V peak, UL's best rating. If the magnitude of the surge is greater than the capacity of the surge protection components, the M5400-PM's Protect or Disconnect Circuitry will disconnect your equipment in order to protect it. The M5400-PM will need to be repaired or replaced by Panamax if this occurs within the product’s 3 year warranty.

Five Isolated Outlet Banks
The M5400-PM is designed to provide noise isolation between the outlet banks so that any noise created by A/V components plugged into the M5400-PM cannot contaminate the power going to equipment plugged into the other outlet banks of the M5400-PM.

Sequential Startup/Shutdown
Complex audio/video systems may be susceptible to voltage transients generated internally at start-up/shutdown if all of the equipment is powered on or off at the same time. This can cause speaker "thumps" which are not only annoying but can also damage the speakers and/or trip product circuit breakers. The M5400-PM is designed to eliminate these transients by providing a "start-up" delay for the High-Current outlets and a "shutdown" delay for the Switched Outlet Banks. This minimizes in-rush current issues by allowing the components plugged into the Switched Outlet Banks to power-up and stabilize before any amplifiers and powered sub-woofers are turned on. This sequence is reversed during shutdown. The amplifiers and powered subwoofers turn off, their power supplies drain, and then the equipment plugged into the Switched Outlet Banks are turned off.

USB Charger, LAN, and Gaming Ports
The M5400-PM features a front panel convenience charger for mp3 players, cell phones, video game controllers, and other small electronics. (NOTE: Some devices may not be compatible with this USB charger.) Add to this an easy-to-access LAN port pass-thru from the rear panel to the front panel for online gaming and a convenience outlet located on the front panel, perfect for gaming systems and other electronics.

Voltage Sense Trigger
The M5400-PM voltage sense trigger input uses a standard 3.5mm (1/8") mini-mono plug. This feature provides an ON/OFF trigger for the M5400-PM using a Direct Current voltage signal. Many components such as pre-amplifiers and receivers have a DC trigger built in, and will transmit a constant power signal when turned on and in use. The presence of this power signal will turn on the M5400- PM's switched outlets. When the source component is turned off, the voltage trigger signal is also turned off and the M5400-PM's shutdown sequence is initiated. An AC Adapter of the appropriate voltage plugged into a switched outlet may also be used if a DC trigger is not built in.

Protection for Cable/Satellite/Antenna as Well as LAN and Telephone Lines
Coaxial protection circuits achieve optimum signal quality from our new coaxial protectors that have the smallest signal loss on the market - less than 0.5 db of attenuation from 0 MHz to 2.2 GHz. Our upgraded coaxial protection has been specifically designed to virtually eliminate signal loss. The clamping level of 75V will meet the demands of both cable and satellite voltage while minimizing exposure to damaging spikes and surges.

Digital video recorders and satellite TV receivers require a telephone line connection for TV show scheduling and/or Pay-Per-View services. The M5400-PM also provides surge protection for this line. One pair of RJ-11 telephone jacks is provided for this. The circuitry utilizes auto-resetting PTCRs and solidstate SIDACtors for reliability and unsurpassed protection. The clamping level of the M5400- PM's telephone protector is 260 volts. This will allow typical ring voltage (90-130VAC) and operating battery voltage (-48DC) to pass through the circuit and still protect the modem in your satellite receiver from damage.

Protection circuits for 10/100 baseT Ethernet lines. Incoming LAN line MUST be plugged into the LINE jack. Patch cord to the equipment MUST be plugged into the EQUIP jacks. 1 LAN jack goes to the front panel output jack. 8 wire protection, 52V clamping.